My first stair|Forum|WOOD DESIGNER

Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Feed sp_TopicIcon
My first stair
Avatar
Ness

Forum Posts: 1939
Subscriber Since:
October 4, 2012
sp_UserOfflineSmall Offline
41
September 15, 2016 - 8:20 am
sp_Permalink sp_Print

Hi Stig,

Yes, I’m sure that the back of the pockets are extended 28mm, I’m not sure why this came about.

If the stairs are painted filling in the pockets is certainly easier to do.

You’ll have to see directly with Stefan for compensation.

All the best,

Ness

Avatar
Guest
40
September 13, 2016 - 9:36 am
sp_Permalink sp_Print

Ness said
Hi Sig,

Sorry to get back so late but I have been away this last week.

It seems that the step housings in the dxf parts are extended 28mm on the back edge.

This has only appeared in the sting dxf files and could be a configuration error in the dxf set up.

The only explanation I can see is that I’ve forgot to re-set the dxf config after using StairDesigner for another client, so I do apologize for this.

As the housing are already routed out, to fill the extra hole, I would suggest gluing  to the back edge of the steps, either a continuous batten:

step-modif-010.pngImage Enlarger

or 2 gussets :

step-modif-020.pngImage Enlarger

Both solutions should work and give an elegant finish.

Sorry again about my mistake,

All the best,

Ness

Hi,

Well, the stringboards are gonna be painted, so i guess it will be less work to fill 28mm of the back of the step-pocket.

Are you sure it is the back of the pocket that is extended ?

And…dont you think this is a money-back issue for the stair-file?

thx

Stig

Avatar
Ness

Forum Posts: 1939
Subscriber Since:
October 4, 2012
sp_UserOfflineSmall Offline
39
September 13, 2016 - 9:16 am
sp_Permalink sp_Print

Hi Sig,

Sorry to get back so late but I have been away this last week.

It seems that the step housings in the dxf parts are extended 28mm on the back edge.

This has only appeared in the sting dxf files and could be a configuration error in the dxf set up.

The only explanation I can see is that I’ve forgot to re-set the dxf config after using StairDesigner for another client, so I do apologize for this.

As the housing are already routed out, to fill the extra hole, I would suggest gluing  to the back edge of the steps, either a continuous batten:

step-modif-010.pngImage Enlarger

or 2 gussets :

step-modif-020.pngImage Enlarger

Both solutions should work and give an elegant finish.

Sorry again about my mistake,

All the best,

Ness

sp_PlupAttachments Attachments
Avatar
Guest
38
September 13, 2016 - 8:49 am
sp_Permalink sp_Print

*BUMP*

Avatar
Guest
37
September 11, 2016 - 10:31 am
sp_Permalink sp_Print

Ness said
Hi Sig,

Here are your files.

Hope the build goes OK for you.

Keep us updated.

All the best,

Ness

Hi Ness,

I cut out all of the parts a while ago, and today i was about to fit them all together.

But…. All pockets in the stringboards ( for steps) is approx 28mm too wide !! And when i now check the drawings, i see the steps will not fit… How could this happen ?

Avatar
Ness

Forum Posts: 1939
Subscriber Since:
October 4, 2012
sp_UserOfflineSmall Offline
36
June 27, 2016 - 4:42 am
sp_Permalink sp_Print sp_EditHistory

Hi Stig,

Thanks for posting your photo, it looks great!

All the best,

Ness

Avatar
Guest
35
June 21, 2016 - 6:24 pm
sp_Permalink sp_Print

Thanks !!

Installation of my first stair right now…2016-06-21-20.22.16.jpgImage Enlarger

sp_PlupAttachments Attachments
Avatar
Ness

Forum Posts: 1939
Subscriber Since:
October 4, 2012
sp_UserOfflineSmall Offline
34
June 21, 2016 - 5:07 pm
sp_Permalink sp_Print

Hi Sig,

Here are your files.

Hope the build goes OK for you.

Keep us updated.

All the best,

Ness

sp_PlupAttachments Attachments
Avatar
Guest
33
June 21, 2016 - 4:56 pm
sp_Permalink sp_Print

Hi,

thanks, it looks good to me 🙂

Avatar
Ness

Forum Posts: 1939
Subscriber Since:
October 4, 2012
sp_UserOfflineSmall Offline
32
June 21, 2016 - 4:50 pm
sp_Permalink sp_Print

Hi again,

I’ve deleted the last post and set the second flight to 3410 leaving 5mm clearance at each wall.

Can you check to see If this is OK for you and I’ll process your files.

All the best,

Ness

Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online:
Guest(s) 23
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Tom Cleaver: 162
mark nichols: 160
brendan kavanagh: 136
Conor Devoy: 132
Duayne Naugle: 129
Stu Robertson: 104
Zaheer Abbas: 86
Robert Coxhead: 63
Ray: 59
Patrick Maylor: 57
Newest Members:
pg_panel7
hadialnajjar
Isaac
butnariu daniela
Yosi Siboni
dziekan
AKM
Garyh
niharbu
Daniel Jones
Forum Stats:
Groups: 2
Forums: 7
Topics: 2075
Posts: 11386

 

Member Stats:
Guest Posters: 4
Members: 254
Moderators: 0
Admins: 12
Administrators: Ness, Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Darren, Isaac