
October 4, 2012

Hi again,
Sorry I forgot to answer your question about the back grooves.
To make it easier for us to follow, can I suggest that you post a thread per subject ?
In your cabinet, you can adjust the depth of the back groove either using the panel Properties-Links menu :
You can also use a specific sub method, although it seems that you are not using a sub method to set up this cabinet.
All the best,
Ness

October 4, 2012

Hi Buddika Thusitha,
There are several ways to change the frame sections and this depends on how you are working and how you have set them up.
If the component is in bar material, the simplest way is to just change the material in the Properties list:
If the component is in a Quick Design design material it's possible to change the Quick Design material specs:
It's also possible to set the components up as panel materials, in which case you can change the width using the Assembly Edit button:
Hope this is helpful,
All the best,
Ness


July 13, 2017



July 13, 2017



July 13, 2017

Dear Ness,

November 8, 2013

Hi Thusitha, I think you probably saw Ness's reply to one of your other queries. He was away yesterday and today, and we need him to take a look at these particular points, so we apologise for the delay. He'll take a look at your queries on his return. Best regards, Stefan


July 13, 2017



We raised this at the team viewer session, but it was not possible to finish at that time, and we kept it aside.
Here, when we add the middle panel, as per the second image, the front piece gets divided in to two. But we need it in one piece. Please show us how to do that.
Thusitha

October 4, 2012

HI Thusitha,
No problem to draw these designs in Polyboard Pro.
best regards,
Ness
The following users say thank you to Ness for this useful post:
Thusitha Karunatilake

July 13, 2017

Stefan said
Here are the other attachments I've resized for the forum.Thusitha, when you click on 'upload attachment' you will see the maximum size allowed. Please resize future images so they can be uploaded and seen on the forum.
Thanks, Stefan
![]()
Dear Ness,
Please check this attachments and confirm whether all these can be done with Polyboard Pro or not.
Thusitha.

November 8, 2013

The following users say thank you to Stefan for this useful post:
Thusitha Karunatilake
October 4, 2012

Hi Thusitha,
I can't see all the files you have listed in your post but to answer your questions:
Yes, you can set back the back panel 3/4" from the edge, this can be done in Lite and Pro.
Framing can be done in Pro but not in Lite.
All the Face Frame options you show are only active in Polyboard Pro.
The only images I can see in your post are a screen capture showing the Face Frame options in the Structures menu, I can't see the images of your projects.
Can you upload them?
Otherwise from you description you should be able to do what you need with Polyboard Pro.
best regards,
Ness

November 8, 2013

Hi, we'll reply in full as soon as possible. I know it's urgent as you would like to upgrade from Polyboard Lite to Polyboard Pro.
I can only see 2 images attached though, which I think are the same as each other. Can you upload the other items you've referenced in your message. Thanks, Stefan


July 13, 2017

How are you? Hope you are doing good.
In the first attachment, we have shown the back panel of a cupboard. Back board is fixed three quarter of an inch inwards from the outer edge. Is it possible to do with Polyboard Pro?
In the second and third attachments we do the face frame, with two inch frame. In between the drawers we attach a 2.75 inch width piece. This enables us to do finger groves for the drawers.
In the fourth attachment, in your drop down list we have circled some options. Are they included in Polyboard Pro, or we have to add them?
We need your confirmation whether we can do all these with Polyboard Pro.
Hope to hear from you shortly.
Regards.
1 Guest(s)