Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
Lost password?
sp_Feed sp_TopicIcon
Request for cut list and plans processing
Avatar
Ness

Forum Posts: 1856
Subscriber Since:
October 4, 2012
Thanked 529 times in 1856 posts
Reputation: 22512
sp_UserOfflineSmall Offline
9
April 17, 2019 - 5:26 am
sp_Permalink sp_Print

Hi Arkadiusz,

You are right, it would be better to have an angle parameter that we could apply separately  to each joint.

I will certainly make this suggestion to the developer team.

Thanks for this feed back.

Best regards,

Ness

Avatar
ARKADIUSZ TECLAW

Forum Posts: 8
Subscriber Since:
March 21, 2019
Thanked 0 times in 8 posts
Reputation: 40
sp_UserOfflineSmall Offline
8
April 13, 2019 - 2:28 pm
sp_Permalink sp_Print

Thank you Ness for the files.

It looks like within one project, a mitre-joint fittings can be of a one kind only… subject to system preference settings 🙁

If I may suggest future development feature: white defining tooling within fittings, the drilling type could have an angle parameter. Of course in most of the cases it would be set to 90 deg, however with some fancy designs it could very useful, e.g fitting horizontal shelf to a sloped side with a cam connector. Now it ends up with a solution like this:

snapshot.pngImage Enlarger

 

unless there is some work around I am not familiar with…

with regards,

Arkadiusz

sp_PlupAttachments Attachments
Avatar
Ness

Forum Posts: 1856
Subscriber Since:
October 4, 2012
Thanked 529 times in 1856 posts
Reputation: 22512
sp_UserOfflineSmall Offline
7
April 12, 2019 - 3:51 pm
sp_Permalink sp_Print

Hi Arkadiu,

Sorry I had forgotten that you had asked this and as this parameter is not saved in the model but in the general Polyboard setup, my Polyboard was not set correctly.

I attach the re-processed  files .

Have a great week-end,

Best regards,

Ness

sp_PlupAttachments Attachments
Avatar
ARKADIUSZ TECLAW

Forum Posts: 8
Subscriber Since:
March 21, 2019
Thanked 0 times in 8 posts
Reputation: 40
sp_UserOfflineSmall Offline
6
April 12, 2019 - 9:29 am
sp_Permalink sp_Print

Thank you Ness for your swift answer.

There is one question though. The fittings between Top&Sides of mitre-joint are not paralel to the side face but are perpendicular to the edge. If you recall I asked in a different post how to change that: https://wooddesigner.org/forum…..-hardware/

which I did. See the attached shapshots for details.snapshot1.pngImage Enlarger

snapshot2.pngImage Enlarger

Can production files be modified to reflect that?

Thank you

Arkadiusz

sp_PlupAttachments Attachments
Avatar
Ness

Forum Posts: 1856
Subscriber Since:
October 4, 2012
Thanked 529 times in 1856 posts
Reputation: 22512
sp_UserOfflineSmall Offline
5
April 12, 2019 - 8:44 am
sp_Permalink sp_Print

Hi Arkadiusz,

Sorry for the delay, but with some of our team away for the last week we have been a bit behind in processing files.

So with our excuses, I attach your manufacturing files.

Please excuse us for any inconvenience caused.

Best regards,

Ness

sp_PlupAttachments Attachments
Avatar
ARKADIUSZ TECLAW

Forum Posts: 8
Subscriber Since:
March 21, 2019
Thanked 0 times in 8 posts
Reputation: 40
sp_UserOfflineSmall Offline
4
April 12, 2019 - 7:59 am
sp_Permalink sp_Print

Hi Wooddesigners

Its been almost a week and I still have not received my production files. Is there a problem with my drawings?

surprised

Avatar
ARKADIUSZ TECLAW

Forum Posts: 8
Subscriber Since:
March 21, 2019
Thanked 0 times in 8 posts
Reputation: 40
sp_UserOfflineSmall Offline
3
April 5, 2019 - 7:22 am
sp_Permalink sp_Print

ups…

here you go.

Avatar
Ness

Forum Posts: 1856
Subscriber Since:
October 4, 2012
Thanked 529 times in 1856 posts
Reputation: 22512
sp_UserOfflineSmall Offline
2
April 5, 2019 - 6:03 am
sp_Permalink sp_Print

Hi Arkadiu,

I’m sorry but I can’t see you file.

Can you upload it again, and don’t forget that after you drag it into the upload window you must then click the “Add Files” button.

Best regards,

Ness

Avatar
ARKADIUSZ TECLAW

Forum Posts: 8
Subscriber Since:
March 21, 2019
Thanked 0 times in 8 posts
Reputation: 40
sp_UserOfflineSmall Offline
1
April 3, 2019 - 11:46 am
sp_Permalink sp_Print

Good Day!

Please, provide production files for the attached project.

This is my first project ever so any feedback would be welcomed.

Thank you.

Forum Timezone: Europe/London
Most Users Ever Online: 67
Currently Online:
20
Guest(s)
Currently Browsing this Page:
1 Guest(s)
Top Posters:
terry: 253
mark nichols: 119
jimbouk: 105
syslab: 97
Christopher Paré: 97
Jack Travis: 77
Duayne Naugle: 73
Tom Cleaver: 63
Rafal Meckovski: 62
Peter Brown: 62
Newest Members:
Lindsay Hiller
Nicolas Dupont
naseer ahmed
Erik Carrillo
Walter Diana
Josh Cheong
Octavian Pal
papades lag
Caiuteanu Vlad
Guntis Kuzmickis
Forum Stats:
Groups: 2
Forums: 8
Topics: 1137
Posts: 6589

 

Member Stats:
Guest Posters: 3
Members: 96933
Moderators: 1
Admins: 7
Administrators: Ness, Stefan, michel melon, Carole Bosy, admin, Sunil Jaiswal, ipatrick
Moderators: Alex