Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
Lost password?
sp_Feed sp_TopicIcon
Wrong door hinge location, built in frame door .
Avatar
Puuslik

Forum Posts: 41
Subscriber Since:
April 1, 2015
Thanked 1 times in 41 posts
Reputation: 238
sp_UserOfflineSmall Offline
4
June 15, 2021 - 7:01 pm
sp_Permalink sp_Print

Hi!

Now is much understandable.

Best wishes!

Ain

Avatar
Michel

Forum Posts: 914
Subscriber Since:
August 7, 2014
Thanked 185 times in 914 posts
Reputation: 9204
sp_UserOfflineSmall Offline
3
June 1, 2021 - 8:53 pm
sp_Permalink sp_Print

Hi,

 

Here is the answer from the developers and a modified cabinet 

PolyBoard does not generate machining files for bars.

Therefore when assembled parts are set with bars (v/s panels), the bars
are not illustrated in the machining report, and their toolings are shown
next to the central panel, with relative coordinates.

This draws the attention on the fact that those toolings are located out
of the central panel, and should be machined separately on bars.

                                          ______________

Now if instead of bars the setting is done with panels, the part assembled
components will be displayed as independant sub-parts with their own
machining details.

Attached is a modified cabinet file (one door assembled with a panel frame),
as well as the corresonding frame machining PDF printout.

 

regards

Michel 

Avatar
Michel

Forum Posts: 914
Subscriber Since:
August 7, 2014
Thanked 185 times in 914 posts
Reputation: 9204
sp_UserOfflineSmall Offline
2
May 31, 2021 - 10:53 am
sp_Permalink sp_Print

Hi,

 

You do not have a typical built-in situation here as you have recessed the top and overpassed the top by using a groove type on your door. However, your door remains a built-in type. 

 

You need to look at your rule in the fitting link, which is taking as reference the overpassing panel, which is still your top. So PB will take 100 mm from the top inside to drill your hinge.  In this specific case, you need your rule to look at the underpassing panel which is your door even if you overpassed it with a groove type towards your top. If you change the rule to underpassing the 100 mm will be correct according to your need. 

 

I will pass the information to our developers and revert with an answer soon about the second question.

 

 

regards

Michel 

Avatar
Puuslik

Forum Posts: 41
Subscriber Since:
April 1, 2015
Thanked 1 times in 41 posts
Reputation: 238
sp_UserOfflineSmall Offline
1
May 26, 2021 - 7:30 am
sp_Permalink sp_Print

Hi !

I have problem with wood-frame door hinge location.

From top or bottom edge my rule is 100 mm, but sample cabinet ( built in door) program adds top thickness of 18 mm. Door drilling  must be now 118 mm. Where is our not understanding?

Another question is print preview tooling outputs. Why we don't see the hinge borehole measurement on door frames. There are no door frames in the selection at all! Print preview output show the central panel with the measure of the hinges, but it is not from the edge of the door. Important is to check the dimensions before drilling the holes in the frames ( drilling machine is manual not cnc)

I added a file in which the holes for hinges was wrong.

Ain

Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online: Ventsislav Gyondrov, pinku ch, balazs szekeres, Marcelo Homem, GUILLERMO SEMA
Guest(s) 1
Currently Browsing this Page:
1 Guest(s)
Top Posters:
terry: 253
mark nichols: 157
Tom Cleaver: 144
Kerf Works: 143
Conor Devoy: 132
Duayne Naugle: 124
brendan kavanagh: 112
jimbouk: 105
Syslab Corp: 103
Stu Robertson: 102
Newest Members:
GUILLERMO SEMA
jaydana singfield
Jesús Castillo
Jesús Castillo
lara nikpalj
Andres Perrone
Neil Worthington
Joe C
Henri Gorjanec
Henri Gorjanec
Forum Stats:
Groups: 2
Forums: 7
Topics: 1827
Posts: 10087

 

Member Stats:
Guest Posters: 4
Members: 150916
Moderators: 0
Admins: 12
Administrators: Ness, Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Fatima, Crystal, Jem Turner, Darren