prioritization of offcuts|Forum|WOOD DESIGNER

Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Feed sp_TopicIcon
prioritization of offcuts
Avatar
Alex

Forum Posts: 1822
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
11
July 12, 2024 - 3:13 pm
sp_Permalink sp_Print

After discussion with the development team, you can prioritise the drop by increasing the off-cuts depreciation percentage.

All the best, Alex

Avatar
Alex

Forum Posts: 1822
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
10
July 12, 2024 - 9:44 am
sp_Permalink sp_Print

I have send request to dev team’s to force cut-off first

but the tests seem consistent, by changing Off-cuts quality to max

>

Cheers, Alex

Avatar
Blaž Jašovec

Forum Posts: 8
Subscriber Since:
December 20, 2022
sp_UserOfflineSmall Offline
9
July 12, 2024 - 8:30 am
sp_Permalink sp_Print

hello

Yes i have the parameters set like you, but the resoult is the same.

Avatar
Alex

Forum Posts: 1822
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
8
July 12, 2024 - 7:03 am
sp_Permalink sp_Print sp_EditHistory

Hi,

I think you’re looking for this option

From Optimisation parameters > Advanced tab > Off-Cuts… > Select option “Use Stock follow-up Parameters”

Off-cuts.pngImage Enlarger

Else there is no specific option to force Off-cuts first

I’ll ask to dev teams, if there is better solution or if news option can be create

Hope that’s helpful, Alex

sp_PlupAttachments Attachments
Avatar
Blaž Jašovec

Forum Posts: 8
Subscriber Since:
December 20, 2022
sp_UserOfflineSmall Offline
7
July 11, 2024 - 3:28 pm
sp_Permalink sp_Print

Here are some photos where i have 16mm panel offcut that could be used but it is not insted it is using the full panel IMG_20240711_161238.jpgImage Enlarger

IMG_20240711_161222.jpgImage Enlarger
IMG_20240711_161240.jpgImage Enlarger

Avatar
Isaac

Forum Posts: 52
Subscriber Since:
March 25, 2024
sp_UserOfflineSmall Offline
6
July 11, 2024 - 12:13 pm
sp_Permalink sp_Print

If this is set up this should prioritize using the off-cuts.

Refer to the attached image, this is a job I have used to test and there are 3 x off-cuts used. Even though they are referenced as panel 2/3/5, not panel 1, they are still being used. OC won’t always reference them as number 1 in the list.

OC.pngImage Enlarger

I can continue to run some tests on this.

Are you achieving the same results I am achieving?

Isaac

sp_PlupAttachments Attachments
Avatar
Blaž Jašovec

Forum Posts: 8
Subscriber Since:
December 20, 2022
sp_UserOfflineSmall Offline
5
July 11, 2024 - 10:40 am
sp_Permalink sp_Print

Hello,

I have it set like this, but i keep seeing that the program still prefers using full panels if the optimization is better. So is there an option that regardles of the optimization quality it prioritzes the offcuts?

Avatar
Isaac

Forum Posts: 52
Subscriber Since:
March 25, 2024
sp_UserOfflineSmall Offline
4
July 11, 2024 - 10:18 am
sp_Permalink sp_Print

Hello,

My apologies, I will explain for OptiCut.

You can decide if you recover off-cuts or not in the stock options: Tools>Stocks Follow Up (see image).

Stock-Follow-Up.pngImage Enlarger

When you recover off-cuts OptiCut will always first check these before going to full panels. If the pieces do not fit on the off-cut material, OptiCut will skip it.

If you need further explanation, let me know,

Isaac

sp_PlupAttachments Attachments
Avatar
Blaž Jašovec

Forum Posts: 8
Subscriber Since:
December 20, 2022
sp_UserOfflineSmall Offline
3
July 11, 2024 - 9:45 am
sp_Permalink sp_Print

I am using opticut. Is there an option fore this in opticut

Avatar
Isaac

Forum Posts: 52
Subscriber Since:
March 25, 2024
sp_UserOfflineSmall Offline
2
July 11, 2024 - 9:40 am
sp_Permalink sp_Print

Hello,

You are able to set a priority to each of your panels in your panel stock. Refer to image:

 

Image-1.pngImage Enlarger

If your off-cut material has a higher priority to your stock material, OptiNest should choose the off-cut material first.

Regards,

Isaac

sp_PlupAttachments Attachments
Forum Timezone: Europe/London
Most Users Ever Online: 286
Currently Online:
Guest(s) 20
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Ness: 1939
Tom Cleaver: 162
mark nichols: 160
Conor Devoy: 139
brendan kavanagh: 136
Duayne Naugle: 130
Stu Robertson: 104
Zaheer Abbas: 96
Patrick Maylor: 63
Robert Coxhead: 63
Newest Members:
Vicky Hope
Stephen Vis
James
douaihytech
Emmanuel Sacco
MateiCL
Brian Serrao
Allister Griffin
Martin Ahlström
luis parreira
Forum Stats:
Groups: 2
Forums: 7
Topics: 2158
Posts: 11743

 

Member Stats:
Guest Posters: 4
Members: 287
Moderators: 0
Admins: 11
Administrators: Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Darren, Isaac