Adding Edge-Banding to Specific Edges|Forum|WOOD DESIGNER

Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Feed sp_TopicIcon
Adding Edge-Banding to Specific Edges
Avatar
Tom Jackson
Member

Full
Forum Posts: 33
Member Since:
January 24, 2023
sp_UserOfflineSmall Offline
5
July 25, 2023 - 4:54 pm
sp_Permalink sp_Print

Hi Michel,

Brilliant. I’ve managed to add the specific edgebanding for the edges required thank you. But as far as the system highlighting the newly edged end panels and counter in render view – It is not showing. Perhaps there is a slight oversight on my end. We can discuss this in our meeting tomorrow.

Cheers,

Tom

Avatar
Michel

Moderator
Forum Posts: 998
Member Since:
August 7, 2014
sp_UserOfflineSmall Offline
4
July 25, 2023 - 1:18 pm
sp_Permalink sp_Print

Hi tom,

 

When you add the end panel and the edgeband, it will show the band in red if you have taken the one showing the red, of course.

 

regards

Michel 

Avatar
Tom Jackson
Member

Full
Forum Posts: 33
Member Since:
January 24, 2023
sp_UserOfflineSmall Offline
3
July 25, 2023 - 12:43 pm
sp_Permalink sp_Print

Hi Michel,

Ahhh…I was looking for another single panel menu. I vaguely remember you mentioning something about end panels being single panels, I was looking under single panel fittings though.

Is there a way for the render to show red for the end panels and countertop once I added the edge banding? Or do I have to check this method every time via the reports…?

Cheers,

Tom

Avatar
Michel

Moderator
Forum Posts: 998
Member Since:
August 7, 2014
sp_UserOfflineSmall Offline
2
July 25, 2023 - 11:07 am
sp_Permalink sp_Print

Hi Tom,

 

The end panels, countertops and fillers in a project are single panels and not controlled by the edging submethod. While adding the panels, you have the edging parameter in the window that allows you to add edging. Just select the side you need edging on and set the parameter. 

edging.pngImage Enlarger

 

Regards,

Michel 

sp_PlupAttachments Attachments
Avatar
Tom Jackson
Member

Full
Forum Posts: 33
Member Since:
January 24, 2023
sp_UserOfflineSmall Offline
1
July 25, 2023 - 9:52 am
sp_Permalink sp_Print

Hi everyone,

I need assistance with adding edge banding to specific edges on End Panels & Countertops. I only want the visible edges to have edge banding, excluding the wall-facing and floor-facing edges, as well as the top of the end panels touching the underside of the counter.

As you can see in the attached image, the visible edges of the end panels and countertop are not red – Are there other ways PolyBoard lets you know edging has been added?

Seat-Drawers-edge-band-picture.jpgImage Enlarger

Please let me know if you need any further clarification.

Thank you! Tom

Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online:
Guest(s) 30
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Ness: 1939
Tom Cleaver: 162
mark nichols: 160
Conor Devoy: 139
brendan kavanagh: 136
Duayne Naugle: 130
Stu Robertson: 104
Zaheer Abbas: 91
Robert Coxhead: 63
Patrick Maylor: 63
Newest Members:
Jordan Desroches
Jeremy Weber
Qsryche
Sungdo Yusung
Alex test
Gavin Weber
Martin Ahlström
Mario Audisho
mr.jacob.bagoandas@gmail.com
Adam Loiselle
Forum Stats:
Groups: 2
Forums: 7
Topics: 2140
Posts: 11670

 

Member Stats:
Guest Posters: 4
Members: 277
Moderators: 0
Admins: 11
Administrators: Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Darren, Isaac