Few questions about a wardrobe|Forum|WOOD DESIGNER

Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Feed sp_TopicIcon
Few questions about a wardrobe
Avatar
Alex

Forum Posts: 1722
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
2
February 11, 2022 - 2:12 pm
sp_Permalink sp_Print

Hi,

 

– On the cutting list for the Fixed Shelf, the measurement shows in a weird way, at least we think so. 
Is it possible to change so that the Height instead is named Width and the Width instead is named Depth?

 

Not possible, this principle is also used to give the right grain direction into cutlist when it is used

 

-In the cutting list for the bottoms of the drawers, they have the same measurement, but it shows as 7 pieces on one page of the cutting list, and 1 piece on one page of the cutting list. Is it because the 1 drawer is in a different section of the wardrobe?

Looking at your cabinet, you have 7 identical drawer inner elements because you had identical zone widths, but your left drawer has a different overlap (full overlap on the left side, and half overlap on vertical division). All other have 2 half overlap

drw.pngImage Enlarger

-When I add a plinth, it is shorter than the whole furniture!? We would like it to have the same width. The wardrobe is going to be built in between to walls, with fillers on the sides. Is it possible to change this when you add/put in the plinth or do we just change the measurement afterwards when it already is in place?

To kept your original cabinet dimension you can put you external zone to Outer positioning

extout.pngImage Enlarger

 

All the best, Alexandre

sp_PlupAttachments Attachments
Avatar
Ola svensson

Forum Posts: 43
Subscriber Since:
January 20, 2022
sp_UserOfflineSmall Offline
1
February 11, 2022 - 1:32 pm
sp_Permalink sp_Print sp_EditHistory

Hi,

I have some questions about a wardrobe.

On the cutting list for the Fixed Shelf, the measurement shows in a weird way, at least we think so. 
Is it possible to change so that the Height instead is named Width and the Width instead is named Depth?

In the cutting list for the bottoms of the drawers, they have the same measurement, but it shows as 7 pieces on one page of the cutting list, and 1 piece on one page of the cutting list. Is it because the 1 drawer is in a different section of the wardrobe?

When I add a plinth, it is shorter than the whole furniture!? We would like it to have the same width. The wardrobe is going to be built in between to walls, with fillers on the sides. Is it possible to change this when you add/put in the plinth or do we just change the measurement afterwards when it already is in place?

Thanks, Caroline

Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online:
Guest(s) 29
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Tom Cleaver: 162
mark nichols: 160
brendan kavanagh: 136
Conor Devoy: 132
Duayne Naugle: 129
Stu Robertson: 104
Zaheer Abbas: 86
Robert Coxhead: 63
Ray: 59
Patrick Maylor: 57
Newest Members:
pg_panel7
hadialnajjar
Isaac
butnariu daniela
Yosi Siboni
dziekan
AKM
Garyh
niharbu
Daniel Jones
Forum Stats:
Groups: 2
Forums: 7
Topics: 2075
Posts: 11392

 

Member Stats:
Guest Posters: 4
Members: 254
Moderators: 0
Admins: 12
Administrators: Ness, Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Darren, Isaac