Avatar

Lost password?
Advanced Search

— Forum Scope —




— Match —





— Forum Options —





Minimum search word length is 3 characters - maximum search word length is 84 characters

sp_Feed Topic RSS sp_TopicIcon
Increasing Groove size on drawer boxes
August 8, 2017
3:35 pm
Avatar
Elliot Gay

Forum Posts: 36
Member Since:
October 8, 2016
Thanked 0 times in 36 posts
Reputation: 182
sp_UserOfflineSmall Offline

Yes sorry the materials coming out at 18.4mm (meant to be 18mm) and the ’12mm’ tool is approx 11.8mm so i think this is where the problem is.

Cheers

Elliot

August 8, 2017
3:20 pm
Avatar
Ness

Forum Posts: 1558
Member Since:
October 4, 2012
Thanked 446 times in 1558 posts
Reputation: 18946
sp_UserOfflineSmall Offline

Hi Elliot,

Yes add the slack to the groove thickness.

You said that the material was 5mm thicker, I’m supposing that you meant 0.5mm?

cheers,

Ness

The following users say thank you to Ness for this useful post:

Elliot Gay
August 8, 2017
3:06 pm
Avatar
Elliot Gay

Forum Posts: 36
Member Since:
October 8, 2016
Thanked 0 times in 36 posts
Reputation: 182
sp_UserOfflineSmall Offline

Hi Ness, thanks for this – i thinks its a combination of the tooling being slightly under the 12mm as stated on the tool and the material being slightly over the 18mm that its meant to be.

If i was to add slack in the grooving and oversizing presumably it would be on the ‘thickness’?

Regards

Elliot

August 8, 2017
9:40 am
Avatar
Ness

Forum Posts: 1558
Member Since:
October 4, 2012
Thanked 446 times in 1558 posts
Reputation: 18946
sp_UserOfflineSmall Offline

HI Elliot,

The groove on the drawer sides is in the Drawer sub method.

drawer-subs.pngImage Enlarger

The width of the groove is set by the thickness of the panel used for the drawer bottom.

You can add slack to this by using the Groove and oversizing submethod.

However, from what you say it seems that you’ll need to change the thickness of the drawer bottom material.

All the best,

Ness

sp_PlupAttachments Attachments

The following users say thank you to Ness for this useful post:

Elliot Gay
August 7, 2017
9:23 pm
Avatar
Elliot Gay

Forum Posts: 36
Member Since:
October 8, 2016
Thanked 0 times in 36 posts
Reputation: 182
sp_UserOfflineSmall Offline

Hi im trying to increase the size of the 18mm groove (10mm deep) on the bottom of the side of the drawers and i cant see where is this in the fittings  – i can see the 2mm / 18.4.

The material that we are running for this job is coming in at approx 5mm thicker so need to allow for this.

Please see attachment.

Kind Regards

Elliot

Forum Timezone: Europe/London

Most Users Ever Online: 58

Currently Online:
17 Guest(s)

Currently Browsing this Page:
1 Guest(s)

Top Posters:

terry: 253

mark nichols: 117

jimbouk: 105

Christopher Paré: 97

Jack Travis: 66

Peter Brown: 61

Duayne Naugle: 56

Rafal Meckovski: 53

Thusitha Karunatilake: 52

Antony S Brighton: 47

Member Stats:

Guest Posters: 2

Members: 82066

Moderators: 4

Admins: 3

Forum Stats:

Groups: 2

Forums: 8

Topics: 862

Posts: 5205

Newest Members:

JUSTIN roberts, Steve Yates, rick arrascue, jay moothy, Christopher Cote, Philip Grossenbacher, tim buam, Kathie Verderber, Miles Rahimi, Dafni Tsolakidou

Moderators: michel melon: 226, D-Alexandre: 72, admin: 0, urbanelement: 0

Administrators: Ness: 1558, Stefan: 583, Carole Bosy: 16