Wood Designer forum

Sign up to Premium Support
to speak to our technical team

Nesting angles again|Forum|WOOD DESIGNER

Avatar
sp_Search Search
Advanced Search
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Search Search
sp_Feed sp_TopicIcon
Nesting angles again
Avatar
Conor Devoy

Forum Posts: 132
Subscriber Since:
January 28, 2018
sp_UserOfflineSmall Offline
9
November 15, 2018 - 5:24 pm
sp_Permalink sp_Print

D-Alexandre said
Only using polyboard abilities

Meuble-incli.jpgImage Enlarger

Meuble-incli2.jpgImage Enlarger

wink  

Very nice.

Avatar
Ness
Forum Posts: 1939
Subscriber Since:
October 4, 2012
sp_UserOfflineSmall Offline
8
November 15, 2018 - 12:41 pm
sp_Permalink sp_Print

Hi Conor,

You should get the panels cut to net dims and only over sizing added, so should be OK.

Cheers,

Ness

Avatar
Alex

Forum Posts: 1757
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
7
November 15, 2018 - 11:51 am
sp_Permalink sp_Print

Only using polyboard abilities

Meuble-incli.jpgImage Enlarger

Meuble-incli2.jpgImage Enlarger

wink

sp_PlupAttachments Attachments
Avatar
Conor Devoy

Forum Posts: 132
Subscriber Since:
January 28, 2018
sp_UserOfflineSmall Offline
6
November 15, 2018 - 10:47 am
sp_Permalink sp_Print sp_EditHistory

D-Alexandre said
Hi,

For export to my 3 axis CN I use chamfer “Right edge+”

hope that will help you

Right-edge.pngImage Enlarger

and set chamfer to default to have right angle on production documents

All the best, Alex  

Thanks Alex, that’s a complicated cabinet.

Avatar
Conor Devoy

Forum Posts: 132
Subscriber Since:
January 28, 2018
sp_UserOfflineSmall Offline
5
November 15, 2018 - 10:45 am
sp_Permalink sp_Print

Ness said
Hi both,

Please make sure that in your Polyboard to Optinest post processor the dimensions are set to “Overall”.

on-dimension.jpgImage Enlarger

Best regards,

Ness  

Thanks Ness, everyday is a school day. This doesn’t impact on my gable hinge hole problem I had last week where the edging was not allowed for?

Regards, Conor

Avatar
Ness
Forum Posts: 1939
Subscriber Since:
October 4, 2012
sp_UserOfflineSmall Offline
4
November 15, 2018 - 7:54 am
sp_Permalink sp_Print sp_EditHistory

Hi both,

Please make sure that in your Polyboard to Optinest post processor the dimensions are set to “Overall”.

on-dimension.jpgImage Enlarger

Best regards,

Ness

sp_PlupAttachments Attachments
Avatar
Alex

Forum Posts: 1757
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
3
November 15, 2018 - 7:48 am
sp_Permalink sp_Print sp_EditHistory

Hi,

For export to my 3 axis CN I use chamfer “Right edge+”

hope that will help you

Right-edge.pngImage Enlarger

and set chamfer to default to have right angle on production documents

All the best, Alex

sp_PlupAttachments Attachments
Avatar
Guest
2
November 15, 2018 - 7:30 am
sp_Permalink sp_Print

We also had the same issue and would like to know an answer.

Avatar
Conor Devoy

Forum Posts: 132
Subscriber Since:
January 28, 2018
sp_UserOfflineSmall Offline
1
November 14, 2018 - 9:14 pm
sp_Permalink sp_Print

Hi all,

I’m doing my first under stair project and I added 10mm to chamfered edges as per my previous nesting angles post question/answer.

This all seemed fine and when I explode the drawing in polyboard there is 10mm oversizing showing.

However when I nested the panels I didn’t get the 10mm extra, I got the net size.

Is there something else to do in optinest?

Thanks, Conor

sp_Feed
Go to top
Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online:
Guest(s) 30
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Ness: 1939
Tom Cleaver: 162
mark nichols: 160
brendan kavanagh: 136
Conor Devoy: 132
Duayne Naugle: 130
Stu Robertson: 104
Zaheer Abbas: 86
Robert Coxhead: 63
Patrick Maylor: 62
Newest Members:
Keith Shelley
Kate Polak
zorsim
Janio Soares
Kitchen Jockey
pg_panel7
hadialnajjar
Isaac
butnariu daniela
Yosi Siboni
Forum Stats:
Groups: 2
Forums: 7
Topics: 2102
Posts: 11509

 

Member Stats:
Guest Posters: 4
Members: 260
Moderators: 0
Admins: 11
Administrators: Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Darren, Isaac