Tool Identifiers|Forum|WOOD DESIGNER

Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Feed sp_TopicIcon
Tool Identifiers
Avatar
Alex

Forum Posts: 1659
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
7
August 22, 2022 - 8:27 am
sp_Permalink sp_Print sp_EditHistory

Hi, 

 

I have moved your message to the correct section so that it can be dealt with more quickly instead of going to the sorting area which can delay the response by another 2 days

Polyboard cannot change the sub-methods of the drawers.

The best solution at the moment is to allocate one “fitting” per slider length.

Drawers.pngImage Enlarger

 

All the best, Alex

sp_PlupAttachments Attachments
Avatar
Stu Robertson

Forum Posts: 104
Subscriber Since:
December 7, 2018
sp_UserOfflineSmall Offline
6
August 21, 2022 - 10:49 pm
sp_Permalink sp_Print

Thanks Alex

So going from your Hettich example if you change say the depth the Fitting Links Sub-Method (you have created) will change to suit the correct drawer depth of drawer? if so very helpful.

regards

Dave

Avatar
Alex

Forum Posts: 1659
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
5
August 18, 2022 - 1:26 pm
sp_Permalink sp_Print sp_EditHistory

Hi,

 

The data range is a parametric system for positioning hardware link

I have worked on the document but it is still in French and not yet translated

 

In the cabinet attached you can see how it work with old Hettich setup

You can change Cabinet in:

 

>Depth to see runner fitting change

>Height to see Front fitting change

>Width to see link between front and drawers bottom change

 

But data Range can’t change drawers in height or depth

 

Following your Cabinet Cl_Base

Between Frontage (OverPassing – P ) and drawers bottom (Underpassing – N)

If like attached screen shoot

Data-R.pngImage Enlarger

You used data range rule Link (Upon the rule) The rule Following ( Underpassing -N) part and here N part is Drawer bottom

And at line Beyonde value of 700 mm you select fittings

when drawers bottom have height beyond 700, PolyBoard adding fitting

 

Hope my explain Helpful, All the best Alex

sp_PlupAttachments Attachments
Avatar
Stu Robertson

Forum Posts: 104
Subscriber Since:
December 7, 2018
sp_UserOfflineSmall Offline
4
August 17, 2022 - 8:12 pm
sp_Permalink sp_Print

Thanks Alex

as noted with previous message

“Can we get some advise on setting up of data range’s, in this example for drawers over 700mm we would like the Fitting (caravan connector) to come into play. I have tried setting up a data range for this rule but couldn’t get it to work so I ended up setting up a Begin/End ‘Rule’ (Bottom/Connector) with -20 outside parameters at 700mm distance which works but gives us an incorrect Fitting number when ordering per job.”

 

regards

Dave

Avatar
Alex

Forum Posts: 1659
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
3
August 17, 2022 - 11:31 am
sp_Permalink sp_Print sp_EditHistory

Hi,

 

Sorry but in your screen shoot i don’t see tool Name/Number into first ligne

tools.pngImage Enlarger

According to the CNC, the T101 or E101 coding becomes 1101.

 

All the best, Alex 

sp_PlupAttachments Attachments
Avatar
Stu Robertson

Forum Posts: 104
Subscriber Since:
December 7, 2018
sp_UserOfflineSmall Offline
2
August 17, 2022 - 3:48 am
sp_Permalink sp_Print

Sorry the CL_-Cabinet-Top-Bin-Drw attachment should not have been attached and is not relevant to this query 

Avatar
Stu Robertson

Forum Posts: 104
Subscriber Since:
December 7, 2018
sp_UserOfflineSmall Offline
1
August 17, 2022 - 3:46 am
sp_Permalink sp_Print

We are trying to use the Tool Identifiers for specific grooving operations but have tried to set them up with little success.

 I have attached some files for reference to an operation we are trying to achieve with our drawer bottoms.

What we are trying to achieve – When a drawer width gets over 700mm we use a Hafele Caravan Carcase Connector to enable fixing of the drawer bottom to Drawer Front to give the bottom some support.

As we don’t have a drill bit the correct size for rebate into bottom so we are trying to get our 10mm End Mill bit to cut out a correct size circle.

I have created Milling 10mm Tool Identifier and allocated this to the Fitting Tooling also setup Customized tools in our BiesseWorks CIX Post-Processor.

But when we process the job the Biesse processor comes up with error on this item and has no tooling allocated.

Is there something we should be doing or setup differently for this to work. As there would other operations we would like to add.

Also can we get some advise on setting up of data range’s, in this example for drawers over 700mm we would like the Fitting (caravan connector) to come into play. I have tried setting up a data range for this rule but couldn’t get it to work so I ended up setting up a Begin/End ‘Rule’ (Bottom/Connector) with -20 outside parameters at 700mm distance which works but gives us an incorrect Fitting number when ordering per job.

 

regards

Dave

 

 

BiesseWorks-Tool-Configuration.jpgImage Enlarger

Bottom_Connector-Rule.jpgImage Enlarger
Caravan-Carcase-Connector.jpgImage Enlarger
Tool-Indentifiers.jpgImage Enlarger

Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online:
Guest(s) 10
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Tom Cleaver: 162
mark nichols: 160
brendan kavanagh: 136
Conor Devoy: 132
Duayne Naugle: 129
Stu Robertson: 104
Zaheer Abbas: 86
Robert Coxhead: 63
Ray: 59
dean price: 56
Newest Members:
Yohaan Chandra
Per Thorsen
karameck@yahoo.com.au
ANETTE PISANI
Luke Maendel
Kirk Everhard
Tanya Snyman
Meelis Rätsep
Namhay-Thinley
KonradK
Forum Stats:
Groups: 2
Forums: 7
Topics: 2053
Posts: 11236

 

Member Stats:
Guest Posters: 4
Members: 237
Moderators: 0
Admins: 11
Administrators: Ness, Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Darren