Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
Lost password?
sp_Feed sp_TopicIcon
Tool mark
Avatar
Conor Devoy

Forum Posts: 75
Subscriber Since:
January 28, 2018
Thanked 0 times in 75 posts
Reputation: 377
sp_UserOfflineSmall Offline
5
May 30, 2019 - 9:31 pm
sp_Permalink sp_Print

Alex said
hi

yes, weeke = woodwoop Post-Pro export?

  

Gotcha , I was thinking in drawer setup. Thanks Alex. 

Avatar
Alex
FRANCE

Forum Posts: 308
Subscriber Since:
January 20, 2017
Thanked 109 times in 308 posts
Reputation: 4268
sp_UserOfflineSmall Offline
4
May 30, 2019 - 9:11 pm
sp_Permalink sp_Print

hi

yes, weeke = woodwoop Post-Pro export?

Avatar
Conor Devoy

Forum Posts: 75
Subscriber Since:
January 28, 2018
Thanked 0 times in 75 posts
Reputation: 377
sp_UserOfflineSmall Offline
3
May 30, 2019 - 9:03 pm
sp_Permalink sp_Print

Alex said
Hi,

Which Post processor you using for export?

if you have some setting to do, you must saw there 

All the best, Alexandre

  

Hi alex, I use bpp5 for Weeke but the tool lines, position length etc. are created in polyboard. Surely it’s in polyboard where you can adjust the parameters? Thanks, conor 

Avatar
Alex
FRANCE

Forum Posts: 308
Subscriber Since:
January 20, 2017
Thanked 109 times in 308 posts
Reputation: 4268
sp_UserOfflineSmall Offline
2
May 30, 2019 - 8:30 pm
sp_Permalink sp_Print

Hi,

Which Post processor you using for export?

if you have some setting to do, you must saw there 

All the best, Alexandre

Avatar
Conor Devoy

Forum Posts: 75
Subscriber Since:
January 28, 2018
Thanked 0 times in 75 posts
Reputation: 377
sp_UserOfflineSmall Offline
1
May 30, 2019 - 12:12 pm
sp_Permalink sp_Print

Hi all.

We make our drawers from a 16mm material with an 8mm by 8mm mortise and tenon.

We use a 6mm down cut spiral tool for this.

When its machining the tenon it stops 3mm shorter than I’d like leaving me with two little peaks that have to be taken off by hand.

I’m attaching two pdfs to indicate what I mean, I’d like the cutter to run on a couple of mils.

Where do I adjust that?

Thanks, Conor

Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online:
Guest(s) 1
Currently Browsing this Page:
1 Guest(s)
Top Posters:
terry: 253
mark nichols: 125
jimbouk: 105
Christopher Paré: 97
syslab: 97
Tom Cleaver: 95
Duayne Naugle: 81
Jack Travis: 77
Conor Devoy: 75
Peter Brown: 62
Newest Members:
Muath Taha
Nate Z
Marcio Marinho Mezzadri
JEELO LOPec
Angel Rodriguez
SIMON BEAMES
Aleksandar Nešovanović
Samuel G
jason morris
Adam Duncan
Forum Stats:
Groups: 2
Forums: 8
Topics: 1216
Posts: 6973

 

Member Stats:
Guest Posters: 3
Members: 106874
Moderators: 0
Admins: 8
Administrators: Ness, Stefan, michel melon, Carole Bosy, Alex, admin, Sunil Jaiswal, ipatrick