Model Cutting List Export|Forum|WOOD DESIGNER

Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Feed sp_TopicIcon
Model Cutting List Export
Avatar
Michel

Forum Posts: 984
Subscriber Since:
August 7, 2014
sp_UserOfflineSmall Offline
9
September 8, 2019 - 11:14 am
sp_Permalink sp_Print

Hi Patrick ,

Here is are the documents 

Regards

Michel 

sp_PlupAttachments Attachments
Avatar
Guest
8
September 8, 2019 - 9:43 am
sp_Permalink sp_Print

Hi Michel!

Thank you so much for your help. I think we’ll have to run with that model, as I can’t see another way of having all equal risers and treads across both flights, and with a constant tread width of greater then 240mm but less then 260mm. 

Thanks again, and if you could please process this model and issue the drawings, we’ll get cracking!

Cheers

Pat

Avatar
Michel

Forum Posts: 984
Subscriber Since:
August 7, 2014
sp_UserOfflineSmall Offline
7
September 4, 2019 - 5:35 pm
sp_Permalink sp_Print sp_EditHistory

Hi Patrick

Here another version

I removed the top step so that the last step will butt into the floor structure as you requested.

Added a step and riser is now 166.21 mm. Does it look OK ? I also added the measurements for you to check

Regards

Michel

sp_PlupAttachments Attachments
Avatar
Guest
6
September 4, 2019 - 9:40 am
sp_Permalink sp_Print

Apologies as well. The reason behind the maximum going length of 258mm, is that we are fabricating the staircase from reclaimed timber, and that is the widest that we can get it.

Avatar
Guest
5
September 4, 2019 - 9:35 am
sp_Permalink sp_Print

Thnks Michel.

We can reduce the length of stair flight 1, in order to alter the going length. If I knew how to do this after the model has been set up I would.

I would rather not have the small step at the top of flight 2, as the top tread neds to butt into the floor structure, and then we are rolling carpet down to cover the structure. therefore no top riser required.

The original length of stair flight 1 can be reduced indefinitely to make the flights match better if that helps?

Ideally if we can reduce the riser height to 165mm or less it would be a big help, as that will then make the gaps compliant with Australian Building Code.

Thoughts?

Pat

Avatar
Michel

Forum Posts: 984
Subscriber Since:
August 7, 2014
sp_UserOfflineSmall Offline
4
September 3, 2019 - 6:02 am
sp_Permalink sp_Print sp_EditHistory

Hi Patrick,

Here is the version without risers and depth changed to 20mm.

What is the reason of the tread width being restricted to 258mm? This can be achieved by reducing the first flight to a length of 2580mm instead of 2640mm and on the second flight changing the landing step from 70 to 107 mm. I would not do it by adding a step as the step height is then getting to low.

Also, I would add a riser on the last step to cover up the floor joist.

Once you approved the final drawing i will send the documents.

Regards

Michel

Avatar
Guest
3
September 2, 2019 - 10:49 pm
sp_Permalink sp_Print

Thanks Michel,

Looks pretty good, however I am limited by a couple of things that no longer comply:

1. Maximum tread width can be 258mm. 

2. We are intending to use open risers.

3. Penetration is to to be each tread recessed into the stringboard by 20mm each side. 

All looks pretty good aside from that though!

Can you please send the cut lists based on that?

Thanks,

Pat

Avatar
Michel

Forum Posts: 984
Subscriber Since:
August 7, 2014
sp_UserOfflineSmall Offline
2
September 2, 2019 - 5:38 pm
sp_Permalink sp_Print

Hi Patrick

I made some changes on the stair to make it more compliant. Check and revert with comments.

You did not define the riser as there is not penetration settings and thickness. Once the stair is OK, I can provide you the set of documents you need to produce the stair.

Regards

Michel

Avatar
Guest
1
September 2, 2019 - 10:33 am
sp_Permalink sp_Print

Hi Wooddesigner.

Third time lucky…..

I was directed by your customer support to upload our stair model to this forum to have the cutting list and pdf’s sent out to us? I have attached the model.

Can you please advise how I get the cutting lists?

Thanks,

Pat

Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online:
Guest(s) 36
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Tom Cleaver: 162
mark nichols: 160
brendan kavanagh: 136
Conor Devoy: 132
Duayne Naugle: 129
Stu Robertson: 104
Zaheer Abbas: 86
Robert Coxhead: 63
Ray: 59
Patrick Maylor: 57
Newest Members:
pg_panel7
hadialnajjar
Isaac
butnariu daniela
Yosi Siboni
dziekan
AKM
Garyh
niharbu
Daniel Jones
Forum Stats:
Groups: 2
Forums: 7
Topics: 2075
Posts: 11390

 

Member Stats:
Guest Posters: 4
Members: 254
Moderators: 0
Admins: 12
Administrators: Ness, Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Darren, Isaac