Nosing Problem|Forum|WOOD DESIGNER

Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Feed sp_TopicIcon
Nosing Problem
Avatar
Guest
5
July 15, 2021 - 7:25 pm
sp_Permalink sp_Print

Yes that sorted it Michel.

Many Thanks

Avatar
Michel

Forum Posts: 998
Subscriber Since:
August 7, 2014
sp_UserOfflineSmall Offline
4
July 13, 2021 - 8:49 pm
sp_Permalink sp_Print

Hi Kevin

 

check your DXF v-carve pp on the stringboard tab. Open the step notches and there is a parameter for lengthening. It could be showing 10mm to the front. This means that all step notches will be extended in the stringer. You have to put this to 0

dxfpp.pngImage Enlarger

 

regards

Michel

sp_PlupAttachments Attachments
Avatar
Guest
3
July 13, 2021 - 7:59 pm
sp_Permalink sp_Print

michel melon said
Hi Kevin 

 

I see no file attached? However, if you want to change the nosing on all steps you must be sure that you did not select a step as it will change for only that step. In order to change all, no selection is allowed/ You can then enter the step parameters and set it to the desired value. 

 

In case it is something else please send me the file and explain what you did 

 

regards

Michel 

  

Hi Michel,

I have selected all treads in general to have 20mm nosing, I then just export the Stringers and treads via VCarve dfx. The nosing on the treads is correct but on the strings the nosing is 30mm.

I did add an attachment but will do so again.

Avatar
Michel

Forum Posts: 998
Subscriber Since:
August 7, 2014
sp_UserOfflineSmall Offline
2
July 13, 2021 - 1:42 pm
sp_Permalink sp_Print

Hi Kevin 

 

I see no file attached? However, if you want to change the nosing on all steps you must be sure that you did not select a step as it will change for only that step. In order to change all, no selection is allowed/ You can then enter the step parameters and set it to the desired value. 

 

In case it is something else please send me the file and explain what you did 

 

regards

Michel 

Avatar
Guest
1
July 13, 2021 - 8:52 am
sp_Permalink sp_Print

Hi,

Can anyone help!!.

I have created a staircase design in SD, I have set the nosing at 20mm but it is exporting the dxf with 30mm nosing. What an I overlooking?.

Attached is the file.

 

Cheers

Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online:
Guest(s) 22
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Ness: 1939
Tom Cleaver: 162
mark nichols: 160
Conor Devoy: 137
brendan kavanagh: 136
Duayne Naugle: 130
Stu Robertson: 104
Zaheer Abbas: 90
Robert Coxhead: 63
Patrick Maylor: 63
Newest Members:
Alex test
Gavin Weber
Martin Ahlström
Mario Audisho
mr.jacob.bagoandas@gmail.com
Adam Loiselle
Dov Bolel
David Bragg
wstenholt@gmail.com
Michael Hofer
Forum Stats:
Groups: 2
Forums: 7
Topics: 2135
Posts: 11638

 

Member Stats:
Guest Posters: 4
Members: 273
Moderators: 0
Admins: 11
Administrators: Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Darren, Isaac