Log In
Home
August 7, 2014
Offline
Hi David
let me which files you need from it
regards
Michel
May 28, 2021
Offline
Michel,
I understand I did not convey this earlier. That is my fault. The corrected file looks great. That will work.
August 7, 2014
Offline
Hi David,
Sorry for the delay.
That seems to be an important detail so if you had asked about it I could have helped it but you did not notice it and I have not got such feedback that all steps need to be the same to pass inspection from earlier situations or other members. This was unknown to me.
The software is showing you a 3D view. So always have a check when you want to make a specific type of stair. Here you are not using the landing step ( 19). SD provides the last step (nr19) but there the flight length is measured between the start of your flight and the front of that step 19. The total calculation of the steps includes this nosing and this is creating a difference in length as step 18 passes under the nose of step 19 which is 0.8". Adding to this comes the thickness of the riser 1".
Step 18 is now 1.8" shorter according to your flight length measurements. The only way to solve this is to change the flight length.
The total difference is 1.8" from the front of step 19 ( reference of the flight length) and the back of step 18. As you need all steps to be the same you had to deduct that 1.8" from the flight length as it would be added on by step 18. This would have resulted in all the same steps. Then add 1.8" to the length of the stringboards to fill the gap.
Here is the corrected version for you to check
Regards
Michel
May 28, 2021
Offline
Hey Michel,
I have a question about the stringers for this project. At the top where it connects to the wall (Tread 18) is much shorter than the rest. I did not realize this until I was laying them out. They all need to be the same to pass inspection here. Is there something I am overlooking. I have double checked measurements and the run of the stringers comes out to be the the exact distance from wall to wall. So its not like I need to add another piece and then attach stringers.( so the treads would match) Some help would be greatly appreciated as I am new to the software. Thank you!
August 7, 2014
Offline
Hi David
here are the documents
regards
Michel
August 7, 2014
Offline
Hi David,
No problem. We have some delay in answering for the moment. I will send you the new ones later today
regards
Michel
May 28, 2021
Offline
Hey Michel,
Let me know if I need to make another payment to get the files re-done. Its been a week. Thanks....
May 28, 2021
Offline
Hey Michel,
If it helps....I just need cut stringers and the winding stair tread patterns. The files for viewing angles on the cut stringers also. Thank you
May 28, 2021
Offline
Yes, this is the final. My apologies, builder made wall cladding changes without telling me. Thank you for your help and understanding.
August 7, 2014
Offline
Hi David,
You need to be sure of your project before asking for files. We need some time to process these files. A stairfile is not an immediate issue but the templates is different. I will do it this time but remember this for the future.
Confirm this is your final design before I process
regards
Michel
The following users say thank you to Michel for this useful post:
David SimonMay 28, 2021
Offline
Hey Michel,
Thank you, I did see the refund. I just did site measurements yesterday and they have changed a little. Please see updated attached file. Send over same files as the first time would be greatly appreciated. Thanks!
August 7, 2014
Offline
Hi David,
Here is also our stairfile which includes the parts in Dxf, plan2D Dxf and the 3d Dxf of the stair. You can use any cad program to read these files and on the 2D plan, you have the top view of the stair that allows you to add dimensions and angles on specific parts of the cut stringers.
Have you got your refund as we got the payment twice?
regards
Michel
May 28, 2021
Offline
Thank you Michel,
For the cut stringers-mainly winding portion. Is there anyway to see a detailed view of dimensions and angles for cutting? Thanks
August 7, 2014
Offline
Hi David
Here are the documents
regards
Michel
May 28, 2021
Offline
Thank you Michel. Look forward to it!
August 7, 2014
Offline
Hi David,
I saw the payment. I will provide you with the PDF templates later today. Advise the width of the paper needed. Usually, it is around 900mm.
regards
Michel
May 28, 2021
Offline
Thanks Michel. I thought I had done that already. Re-send over to you after payment?
August 7, 2014
Offline
Hi David,
Our stairfile service is free but does not include the full templates for your stair as this is a paying service.
Here is the link to the payment page (page bottom)
https://wooddesigner.org/store/
Regards
Michel
1 Guest(s)
Usage Policy