Avatar

Lost password?
Advanced Search

— Forum Scope —




— Match —





— Forum Options —





Minimum search word length is 3 characters - maximum search word length is 84 characters

sp_Feed Topic RSS sp_TopicIcon
StairFile Lite
December 8, 2014
6:24 pm
Avatar
Ness

Forum Posts: 1716
Member Since:
October 4, 2012
Thanked 502 times in 1716 posts
Reputation: 21136
sp_UserOfflineSmall Offline

Oh yes, sorry about that,

All the best,

Ness

sp_PlupAttachments Attachments
December 8, 2014
5:35 pm
Avatar
torkild sckerl

Forum Posts: 7
Member Since:
November 15, 2014
Thanked 0 times in 7 posts
Reputation: 39
sp_UserOfflineSmall Offline

Hi Ness

 

think you forgot to attach the file…….

 

Regards Torkild

December 8, 2014
4:59 pm
Avatar
Ness

Forum Posts: 1716
Member Since:
October 4, 2012
Thanked 502 times in 1716 posts
Reputation: 21136
sp_UserOfflineSmall Offline

Hi Torkild,

Here is your StairFile .

Good luck with the building.

Keep us updated on your progress.

All the best,

Ness

December 8, 2014
1:49 pm
Avatar
torkild sckerl

Forum Posts: 7
Member Since:
November 15, 2014
Thanked 0 times in 7 posts
Reputation: 39
sp_UserOfflineSmall Offline

sorry, that was just adding up the mesurements in the pdf, looking at the parameters for the stairs it looks correct.

then thats what we are going for.

 

best regards Torkild

December 8, 2014
1:41 pm
Avatar
torkild sckerl

Forum Posts: 7
Member Since:
November 15, 2014
Thanked 0 times in 7 posts
Reputation: 39
sp_UserOfflineSmall Offline

Hi,

That looks fine, only thing is the overall measurement on the lower stringboard turns out 1720mm max is 1700mm

 

best reg T 

December 8, 2014
1:28 pm
Avatar
Ness

Forum Posts: 1716
Member Since:
October 4, 2012
Thanked 502 times in 1716 posts
Reputation: 21136
sp_UserOfflineSmall Offline

Hi again,

You might find this stair works better:

All the best,

Ness

December 8, 2014
11:47 am
Avatar
torkild sckerl

Forum Posts: 7
Member Since:
November 15, 2014
Thanked 0 times in 7 posts
Reputation: 39
sp_UserOfflineSmall Offline

forgot, righthand side of stairs is wall and only 1700mm wide, (a door is limiting the size)

 

best reg T

December 8, 2014
11:10 am
Avatar
torkild sckerl

Forum Posts: 7
Member Since:
November 15, 2014
Thanked 0 times in 7 posts
Reputation: 39
sp_UserOfflineSmall Offline

Hi,

newels squared, handrail reduced, risers set to 0 penetration, the upper floor will give the last step due to limited space.

 

reg Torkild

December 8, 2014
10:56 am
Avatar
Ness

Forum Posts: 1716
Member Since:
October 4, 2012
Thanked 502 times in 1716 posts
Reputation: 21136
sp_UserOfflineSmall Offline

Hi again,

Looking at your stair I would suggest that :

– you give the sizes on the right of the stair which i presume is the stair well wall.

– if possible you add a small landing step even if it’s only  step overlap to make the junction with the landing

– you make the posts square

– you change the riser penetration to 15

– make string to newel penetration 0

– that you reduce handrail width 

There are a few other points that will need sorting out too to make this project coherent.

I would strongly suggest that you buy a StairFile Pro so that I can give your project a complete review and send you workable stair.

All the best,

Ness

December 8, 2014
10:43 am
Avatar
torkild sckerl

Forum Posts: 7
Member Since:
November 15, 2014
Thanked 0 times in 7 posts
Reputation: 39
sp_UserOfflineSmall Offline

Sorry really imbaressing, uploaded the wrong file! (fliped the inside and outside extreme measurements) and now with newels.

Its has to be an open staircase so therefor no risers needed

No landing step is correct.

I know this starcase is on the limit towards the stairrule but it will work according to my expearience. Room is oly 1700x1900mm

 

best regards Torkild

December 8, 2014
9:52 am
Avatar
Ness

Forum Posts: 1716
Member Since:
October 4, 2012
Thanked 502 times in 1716 posts
Reputation: 21136
sp_UserOfflineSmall Offline

Hello Torkild,

I attach a 2D and 3D Dxf file of your project.

However before I send you back all your manufacturing documents I would just like to be sure that your design is definitely what you want.

I have looked over it and found a few errors that will make it difficult to build for instance:

You have no landing step, riser penetration is too deep, you have no newels, and quite a few other details.

I can send you your manufacturing documents now if you like. Instead though, please consider posting a few more details on the forum about your design so I can explain what you need to change. You can then adjust the design and request your manufacturing documents again.

The other option is to order our StairFile Pro service,  I’ll revise your project for you before sending you the manufacturing documents so you know it is workable and easy to build.

If you’d like to order StairFile Pro (the cost is £95), log in then go to this page:

https://wooddesigner.org/member…..discounts/

Thank you again for joining the Wood Designer Community and requesting your StairFile service.

Speak soon, and all the best,

Ness 

sp_PlupAttachments Attachments
December 8, 2014
9:21 am
Avatar
torkild sckerl

Forum Posts: 7
Member Since:
November 15, 2014
Thanked 0 times in 7 posts
Reputation: 39
sp_UserOfflineSmall Offline

Hi could you please supply me with dxf files for the attached stairs?

 

reg Torkild

Forum Timezone: Europe/London

Most Users Ever Online: 64

Currently Online:
19 Guest(s)

Currently Browsing this Page:
1 Guest(s)

Top Posters:

terry: 253

mark nichols: 119

jimbouk: 105

Christopher Paré: 97

syslab: 93

Jack Travis: 66

Duayne Naugle: 63

Peter Brown: 62

Rafal Meckovski: 58

Thusitha Karunatilake: 54

Member Stats:

Guest Posters: 2

Members: 87791

Moderators: 4

Admins: 3

Forum Stats:

Groups: 2

Forums: 8

Topics: 962

Posts: 5709

Newest Members:

asim majeed, Ian Hampson, jack thom, Niyi Abdul, camilo gomez, Andrei Ionescu, FERNANDO VIDOLINI, Kestas B, Alex Shigakukan, Chris Conway

Moderators: michel melon: 241, D-Alexandre: 114, admin: 0, urbanelement: 0

Administrators: Ness: 1716, Stefan: 608, Carole Bosy: 19