Blum Tip-On Fitting Link|Forum|WOOD DESIGNER

Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Feed sp_TopicIcon
Blum Tip-On Fitting Link
Avatar
Alex

Forum Posts: 1801
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
8
November 1, 2023 - 9:03 am
sp_Permalink sp_Print

Hi,

Can you compress them as zip first

Cheers, Alex

Avatar
Tom Cleaver

Forum Posts: 162
Subscriber Since:
May 18, 2014
sp_UserOfflineSmall Offline
7
November 1, 2023 - 8:46 am
sp_Permalink sp_Print

Hi Alex,

I have tried to upload both a cabinet and a project but they exceed the maximum allowed size….?

Kind regards

Tom

Avatar
Alex

Forum Posts: 1801
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
6
October 30, 2023 - 9:25 am
sp_Permalink sp_Print sp_EditHistory

Hi,

Can you upload your cabinet/project for analysis?

But, For now, there is no automatic solution to apply fittings on double doors from the division on the Left and Right doors, for example, at 50mm and from the centre

or you need to use the function “Apply the rule to Surface Split.”

SP.pngImage Enlarger

The better solution to do this without manual editing is to create two door-types

-Standard door + TiP-on ( with fitting on Top Tip-on single and P rule (door) at 40 from the opening side)
-Double door + Tip-on (with fitting on Top Tip-on 2x single and N rule (from top centre)

Cheers, Alex

sp_PlupAttachments Attachments
Avatar
Tom Cleaver

Forum Posts: 162
Subscriber Since:
May 18, 2014
sp_UserOfflineSmall Offline
5
October 29, 2023 - 8:22 pm
sp_Permalink sp_Print sp_EditHistory

Thanks Alex,

This certainly works with regards to manufacturing drawings. However is there a way to use the existing fitting i.e. [Blum/TipOn] and not [Blum/TipOn x 2]?

Is it possible to use a rule that applies 2 fittings either side of the centre? The same fitting we would use for the single door?

I am trying to keep the hardware list clean and accurate. For example a single door will contain 1 x Blum/TipOn. However, a double door will contain 1 x Blum/TipOnx2. See attached image.

Kind regards

Tom2023-10-29_201936.jpgImage Enlarger

 

sp_PlupAttachments Attachments
Avatar
Alex

Forum Posts: 1801
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
4
October 28, 2023 - 2:23 pm
sp_Permalink sp_Print

Hi,

Maybe by creating 2x tip-on fitting and using rules Unique (single) Following -N panel (Underpassing) here the top, can do the job.

don’t forget to assign hins on this double doors

double-hings.pngImage Enlarger

 
Cheers, Alex

sp_PlupAttachments Attachments
Avatar
Tom Cleaver

Forum Posts: 162
Subscriber Since:
May 18, 2014
sp_UserOfflineSmall Offline
3
October 27, 2023 - 4:10 pm
sp_Permalink sp_Print

Thanks Alex,

This works a treat for the single TipOn door. I can’t however get it to work for the double TipOn doors? For a pair of double doors I would need the fitting in either the top or bottom with a fitting per door? When I put in double doors it just picks up the single door fitting.

2023-10-27_160651.jpgImage Enlarger

2023-10-27_160803.jpgImage Enlarger
2023-10-27_160906.jpgImage Enlarger

Kind regards

Tom

Avatar
Alex

Forum Posts: 1801
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
2
October 27, 2023 - 11:57 am
sp_Permalink sp_Print

Hi

With the single doors, you have 4 directions! depending Fitting side

for example with on Left side you have

The fitting Side direction and is opposite Open Side direction

Top.pngImage Enlarger

LS.pngImage Enlarger

Top direction from fitting side (become / Right If fitting side is Top/Bottom)

Bottom direction from fitting side ( become /Left If fitting side is Top/Bottom)

and this is why you have this 4 options into link Sub-methods

direction.pngImage Enlarger

Another exemple Blum aventos HK-top is not on fitting side but left and right from fitting Side

(Double doors haven’t open side but 2 fittings side L/R or Top/Bottom)

Please see video attached to add on Open side OR Top for exemple

Hope this helpful, Alex

sp_PlupAttachments Attachments
Avatar
Tom Cleaver

Forum Posts: 162
Subscriber Since:
May 18, 2014
sp_UserOfflineSmall Offline
1
October 26, 2023 - 6:54 pm
sp_Permalink sp_Print

Hello,

I have tried to add the Blum Tip-On as a sub method. Unfortunately all I seem to get is the hardware added to the hinge side of the cabinet when using both a single or double door. When I specify the cabinet top or bottom it doesn’t work?? 

I can get this to work manually, but this is a real pain when there are lots of doors.

2023-10-26_184712.jpgImage Enlarger

2023-10-26_185139.jpgImage Enlarger

Kind regards

Tom

sp_PlupAttachments Attachments
Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online:
Guest(s) 14
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Ness: 1939
Tom Cleaver: 162
mark nichols: 160
Conor Devoy: 139
brendan kavanagh: 136
Duayne Naugle: 130
Stu Robertson: 104
Zaheer Abbas: 91
Robert Coxhead: 63
Patrick Maylor: 63
Newest Members:
Jeremy Weber
Qsryche
Sungdo Yusung
Alex test
Gavin Weber
Martin Ahlström
Mario Audisho
mr.jacob.bagoandas@gmail.com
Adam Loiselle
Dov Bolel
Forum Stats:
Groups: 2
Forums: 7
Topics: 2139
Posts: 11662

 

Member Stats:
Guest Posters: 4
Members: 276
Moderators: 0
Admins: 11
Administrators: Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Darren, Isaac