Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
Lost password?
sp_Feed sp_TopicIcon
Pull Finger Cabinets
Avatar
Ness

Forum Posts: 1830
Subscriber Since:
October 4, 2012
Thanked 526 times in 1830 posts
Reputation: 22307
sp_UserOfflineSmall Offline
10
January 4, 2017 - 11:23 am
sp_Permalink sp_Print

Hi Toplina,

I’m still not clear about what your question is.

I would suggest that you sign up as a Full Member so that we can set up a mini-Team Viewer session to talk about it.

Full membership also allow me to make you a custom video to go over specific points. 

Note that when you buy the full version Pro or Pro PP we give you free an hours training and 6 months paid membership.

You can also buy separately a training pack from this page:

https://wooddesigner.org/traini…..g-service/

Wishing you all  the best for 2017,

Ness

Avatar
Toplina Top

Forum Posts: 16
Subscriber Since:
May 16, 2016
Thanked 0 times in 16 posts
Reputation: 83
sp_UserOfflineSmall Offline
9
December 29, 2016 - 10:45 am
sp_Permalink sp_Print

here is the one from Polyboard

Avatar
Toplina Top

Forum Posts: 16
Subscriber Since:
May 16, 2016
Thanked 0 times in 16 posts
Reputation: 83
sp_UserOfflineSmall Offline
8
December 29, 2016 - 9:34 am
sp_Permalink sp_Print

Capture2.JPG

Capture.JPG

This one was downloaded in the quick designs. is there a video or something to see? Many Thanks

sp_PlupAttachments Attachments
Avatar
Ness

Forum Posts: 1830
Subscriber Since:
October 4, 2012
Thanked 526 times in 1830 posts
Reputation: 22307
sp_UserOfflineSmall Offline
7
December 29, 2016 - 8:29 am
sp_Permalink sp_Print

 Hi Toplina,

Not sure what you are referring to in the handle les kitchen, but the back of the islands is made by using a thickness split to double the panel and then a surface split to cut the outer panel into slats:

isalnd-back.pngImage Enlarger

All the best,

Ness

sp_PlupAttachments Attachments
Avatar
Toplina Top

Forum Posts: 16
Subscriber Since:
May 16, 2016
Thanked 0 times in 16 posts
Reputation: 83
sp_UserOfflineSmall Offline
6
December 29, 2016 - 6:31 am
sp_Permalink sp_Print

Thanks Ness. I’m still learning the software for now, once I get somewhere I’m planning to upgrade. Just another question: I have looked at the kitchen design in the quick design, one of the downloads has ” handle-less kitchen” and could not find out how that cabinet was done, I mean the double back’s ?

Thanks

Avatar
Ness

Forum Posts: 1830
Subscriber Since:
October 4, 2012
Thanked 526 times in 1830 posts
Reputation: 22307
sp_UserOfflineSmall Offline
5
December 27, 2016 - 6:13 pm
sp_Permalink sp_Print sp_EditHistory

Hi Toplina,

I’d like to thank Michel for answering so well your question.

I’d just like to add too that as a Full member we try to answer questions posted on this forum faster as well.

Also as well as members videos, include in Premium Support are personalised videos to answer questions, and mini 15 minute Team Viewer sessions to help you through tricky projects.

To make the handles cabinet pulls you need to use the inner tooling functions of Polyboard.

Wishing you all the best for 2017,

Ness

PS: this week we are on holiday so please excuse the delay in answering questions.

Avatar
michel melon
Belgium

Forum Posts: 274
Subscriber Since:
August 7, 2014
Thanked 100 times in 274 posts
Reputation: 3875
sp_UserOfflineSmall Offline
4
December 26, 2016 - 11:13 am
sp_Permalink sp_Print

Hi,

as a free member you have limited access to video tutorials. I advise you to sign in as a full member for only 10 GBP per month . This gives you unlimited access and support. The software you can use for free. Only the software output is blocked. The documents can be send to you after the project is complete. 

take a look at the section plans& pricing to see what you get as a full member 

take a look at the section store/ services to see the different possibilitys to get your documents for the projects as this is a paid service.  

regards

Michel

The following users say thank you to michel melon for this useful post:

Stefan
Avatar
Toplina Top

Forum Posts: 16
Subscriber Since:
May 16, 2016
Thanked 0 times in 16 posts
Reputation: 83
sp_UserOfflineSmall Offline
3
December 26, 2016 - 9:30 am
sp_Permalink sp_Print

is it for paid customers? I’m still learning the software at this stage?

Avatar
michel melon
Belgium

Forum Posts: 274
Subscriber Since:
August 7, 2014
Thanked 100 times in 274 posts
Reputation: 3875
sp_UserOfflineSmall Offline
2
December 25, 2016 - 11:02 am
sp_Permalink sp_Print

Hi ,

yes this is possible and you can find a video in the tutorials under furniture extended 

.

notches.jpgImage Enlarger

regards

michel

sp_PlupAttachments Attachments
Avatar
Toplina Top

Forum Posts: 16
Subscriber Since:
May 16, 2016
Thanked 0 times in 16 posts
Reputation: 83
sp_UserOfflineSmall Offline
1
December 25, 2016 - 6:01 am
sp_Permalink sp_Print

Hi Ness.

Is it possible to get something like this? picture attached. We use a lot of this in Australia where we do cut out on the cabinets to allow for Finger Pull Shadow for doors or drawers.

Thanks

Forum Timezone: Europe/London
Most Users Ever Online: 64
Currently Online: mark nichols
21
Guest(s)
Currently Browsing this Page:
1 Guest(s)
Top Posters:
terry: 253
mark nichols: 119
jimbouk: 105
Christopher Paré: 97
syslab: 97
Jack Travis: 77
Duayne Naugle: 73
Peter Brown: 62
Rafal Meckovski: 61
Thusitha Karunatilake: 55
Newest Members:
Mfundo Zindlovu
Andrea Durán
Shehan KUmara
David Schwartz
Stanley John
Austin Brown
dennis gaibor
Kristoffer Steen
TOTALLY FAKE
Brody Stowers
Forum Stats:
Groups: 2
Forums: 8
Topics: 1089
Posts: 6295

 

Member Stats:
Guest Posters: 3
Members: 94152
Moderators: 3
Admins: 7
Administrators: Ness, Stefan, Carole Bosy, admin, Sunil Jaiswal, ipatrick, Talal
Moderators: michel melon, Alex, Laly Mulero