Wood Designer forum

Help with project |Forum|WOOD DESIGNER

Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Feed sp_TopicIcon
Help with project
Avatar
Duayne Naugle

Forum Posts: 129
Subscriber Since:
March 1, 2015
Thanked 5 times in 129 posts
Reputation: 779
sp_UserOfflineSmall Offline
7
May 28, 2023 - 2:35 am
sp_Permalink sp_Print

Alex said
Hi,

 

In your Stair you use “Joint” to make curve but that can’t work with “landing”

 

Please see this with to show you how you can edit to work

 

Hope that helpful, Alex

  

That was helpful, thanks 

Avatar
Alex

Forum Posts: 1563
Subscriber Since:
January 20, 2017
Thanked 330 times in 1563 posts
Reputation: 16072
sp_UserOfflineSmall Offline
6
May 10, 2023 - 4:49 pm
sp_Permalink sp_Print

Hi,

 

In your Stair you use “Joint” to make curve but that can’t work with “landing”

 

Please see this with to show you how you can edit to work

 

Hope that helpful, Alex

Avatar
Alex

Forum Posts: 1563
Subscriber Since:
January 20, 2017
Thanked 330 times in 1563 posts
Reputation: 16072
sp_UserOfflineSmall Offline
5
May 10, 2023 - 7:12 am
sp_Permalink sp_Print

Hi,

 

Sorry to answer so late, I’m checking with my colleague Michel and will keep you informed, but the double output is not available from the software

 

Cheers, Alex

Avatar
Duayne Naugle

Forum Posts: 129
Subscriber Since:
March 1, 2015
Thanked 5 times in 129 posts
Reputation: 779
sp_UserOfflineSmall Offline
4
May 9, 2023 - 1:17 am
sp_Permalink sp_Print

Duayne Naugle said

Duayne Naugle said

Duayne Naugle said

need some help , i have a stairway to build , it is flared out from bottom to top on both sides with volutes on the bottom , there is a landing at the top of the first flight then turns 90 degrees 2 steps ,  the left and right side into an oval rail that is 39′ in length , i am able to get the stairs pretty close to what i want , but the landing does not work with the flare , i will attach a photo of the job for a better understanding 

  

  

  

in the picture below , it shows a bowed set of stairs up 14 risers , then turns to both sides , left and right for another 3 risers  at the top floor , there is an oval shape that the rail should run continuous , with only 2 volutes at the  bottom of the stairs , tried to start with a straight flight and set a join on both sides to get the curve i want but as soon as i add a landing the join disappears , the landing can only go one way , left or right but  not both ways 

Avatar
Duayne Naugle

Forum Posts: 129
Subscriber Since:
March 1, 2015
Thanked 5 times in 129 posts
Reputation: 779
sp_UserOfflineSmall Offline
3
May 6, 2023 - 2:11 am
sp_Permalink sp_Print

Duayne Naugle said

Duayne Naugle said

need some help , i have a stairway to build , it is flared out from bottom to top on both sides with volutes on the bottom , there is a landing at the top of the first flight then turns 90 degrees 2 steps ,  the left and right side into an oval rail that is 39′ in length , i am able to get the stairs pretty close to what i want , but the landing does not work with the flare , i will attach a photo of the job for a better understanding 

  

  

Avatar
Duayne Naugle

Forum Posts: 129
Subscriber Since:
March 1, 2015
Thanked 5 times in 129 posts
Reputation: 779
sp_UserOfflineSmall Offline
2
May 6, 2023 - 1:53 am
sp_Permalink sp_Print

Duayne Naugle said
need some help , i have a stairway to build , it is flared out from bottom to top on both sides with volutes on the bottom , there is a landing at the top of the first flight then turns 90 degrees 2 steps ,  the left and right side into an oval rail that is 39′ in length , i am able to get the stairs pretty close to what i want , but the landing does not work with the flare , i will attach a photo of the job for a better understanding 

  

Avatar
Duayne Naugle

Forum Posts: 129
Subscriber Since:
March 1, 2015
Thanked 5 times in 129 posts
Reputation: 779
sp_UserOfflineSmall Offline
1
May 6, 2023 - 1:32 am
sp_Permalink sp_Print

need some help , i have a stairway to build , it is flared out from bottom to top on both sides with volutes on the bottom , there is a landing at the top of the first flight then turns 90 degrees 2 steps ,  the left and right side into an oval rail that is 39′ in length , i am able to get the stairs pretty close to what i want , but the landing does not work with the flare , i will attach a photo of the job for a better understanding 

Forum Timezone: Europe/London
Most Users Ever Online: 256
Currently Online:
Guest(s) 70
Currently Browsing this Page:
1 Guest(s)
Top Posters:
terry: 253
Tom Cleaver: 162
mark nichols: 160
Kerf Works: 143
Conor Devoy: 132
brendan kavanagh: 132
Duayne Naugle: 129
jimbouk: 105
Stu Robertson: 104
Syslab Corp: 103
Newest Members:
nathan cassidy
Paul Jones
Mauricio Treviño
Jeff Lee_1
Imantas Mikolevicius
Renier Duvenhage
Peter Corbett
Javier Morales
Jaime Maldonado
Andries Swart
Forum Stats:
Groups: 2
Forums: 7
Topics: 2000
Posts: 10963

 

Member Stats:
Guest Posters: 4
Members: 154250
Moderators: 0
Admins: 12
Administrators: Ness, Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Jem Turner, Darren