Stringer parallel and in line issue|Forum|WOOD DESIGNER

Avatar
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
sp_Feed sp_TopicIcon
Stringer parallel and in line issue
Avatar
Michel

Forum Posts: 998
Subscriber Since:
August 7, 2014
sp_UserOfflineSmall Offline
4
June 29, 2023 - 6:34 pm
sp_Permalink sp_Print

Hi lex,

 

see reply on the other post. The notch has been removed in this versionV2

 

regards

Michel 

Avatar
Alex

Forum Posts: 25
Subscriber Since:
June 9, 2023
sp_UserOfflineSmall Offline
3
June 28, 2023 - 11:05 am
sp_Permalink sp_Print

Hi Alex,

I need the joint cuts to be vertical though. That’s why i cant check if the bottom section is parallel. 

Also if you look on the left stringer that little notch at the top sticking up needs removing.

 

Thanks

Alex

Avatar
Alex

Forum Posts: 1832
Subscriber Since:
January 20, 2017
sp_UserOfflineSmall Offline
2
June 28, 2023 - 10:34 am
sp_Permalink sp_Print sp_EditHistory

Hi,

 

Once manually modified, you leave the standard calculation which is done on an average. 

I would like to point out that the 270 mm width is not sufficient for your stair.

And adjust numbers of part and set to 300mm look to be better here

an Orthogonal Right view will be easier to control, in my opinion

Posting the same message twice only makes them less visible and slows down our processing time.

Regards, Alex

Avatar
Alex

Forum Posts: 25
Subscriber Since:
June 9, 2023
sp_UserOfflineSmall Offline
1
June 28, 2023 - 9:56 am
sp_Permalink sp_Print

Hi Screenshot-2023-06-27-165021-1.jpgImage Enlarger

Screenshot-2023-06-27-170544-1.jpgImage Enlarger

re posted this as i need a reply asap please. 

One other issue i have stumbled upon is when you have to modify the first stringer on a winder. The program does not make the vertical offset the measurement you choose. I understood from you that is because it tries to find the average over all the step noses. 

I have manually changed the top of the stringer to be 50mm from the nose of the step but i don’t know how to make the first step the same as there is no reference points to measure from. 

 

Also once the top of the stringer is modified now how can i check that it is parallel to the bottom of the stringer and at my desired width of 270mm?  

Once this  right stringer is complete the left stringer needs to be exactly the same width of 270mm and finish at the same points. how can I check this too?

Hope that makes sense.  File in question is attached.

Thanks

Alex

Forum Timezone: Europe/London
Most Users Ever Online: 286
Currently Online:
Guest(s) 32
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Ness: 1939
Tom Cleaver: 162
mark nichols: 160
Conor Devoy: 139
brendan kavanagh: 136
Duayne Naugle: 130
Stu Robertson: 104
Zaheer Abbas: 97
Patrick Maylor: 63
Robert Coxhead: 63
Newest Members:
Ron D'Alessandro
Paul123
nathant@cambridgekitchens.co.uk
Jessica Kalbermatter
Vicky Hope
Stephen Vis
James
douaihytech
Emmanuel Sacco
MateiCL
Forum Stats:
Groups: 2
Forums: 7
Topics: 2168
Posts: 11779

 

Member Stats:
Guest Posters: 4
Members: 291
Moderators: 0
Admins: 11
Administrators: Stefan, Michel, Carole, Alex, admin, Laly, ipatrick, Crystal, Fatima, Darren, Isaac